三,漆膜磨耗仪技术参数:
? 主电动机功率:40W
? 修磨电动机:JX5612 220V 90W 2800r/min
? 转盘转速:0~90r/min
? 橡胶砂轮:50*16*13
? 荷重砝码:250克 500克 750克
? 荷重砝码标示重量:500克 750克 1000克
砝码标示重量为施加压于试件表面的重力
荷重砝码上标示的重量=砝码实际重量+加压套重量250克(固定在仪器上)
例:荷重砝码上标示的重量为500克=砝码实际重量250克+加压套250克
? 砂轮平衡砝码:1克 2克 5克 10克 20克 (销轴20克)
? 外形尺寸:主机:220*280*300(长*宽*高)
修磨机:300*205*175(长*宽*高)
? 重量:15Kg
Third, technical parameters:
? Main motor power: 40W
? Grinding motor: JX5612 220V 90W 2800r/min
? Turntable speed: 0~90r/min
? Rubber wheel: 50*16*13
? Load weight: 250g 500g 750g
? Load weight weight: 500g 750g 1000g
The weight of the weight is the weight applied to the surface of the test piece.
The weight indicated on the load weight = the actual weight of the weight + the weight of the compression sleeve is 250 grams (fixed on the instrument)
Example: The weight on the load weight is 500g = the actual weight of the weight is 250g + the pressure set is 250g
? Grinding wheel balance weight: 1g 2g 5g 10g 20g (pin 20g)
? Dimensions: Main unit: 220*280*300 (length * width * height)
Grinding machine: 300*205*175 (length * width * height)
? Weight: 15Kg
四,漆膜磨耗仪工作原理:
严格的控制保证可靠的结果 精心挑选的磨耗轮磨料,质量高 加在磨擦轮上的压力以克为单位 磨耗轮稳定性经严格的质量控制 电子测量转盘转动数 真空吸尘器除磨屑。
漆膜磨耗仪是由二个磨耗砂轮配置于转盘上,当转盘旋转时,左侧一个磨耗砂轮由外向样板表面中心磨擦,而右侧一个磨耗砂轮由样板表面中心向外磨擦。当转盘旋转一周时,在样板表面磨耗的痕迹是由互相重合,并呈X形相交的二园环组成。采用这种方式,其优点是使样板表面各个方向都受到磨擦,克服了一个方向往复运动的耐磨仪的缺点。
Fourth, the working principle:
Strict control guarantees reliable results Carefully selected grinding wheel abrasives, high quality Plus pressure on the grinding wheel in grams of wear wheel stability through strict quality control Electronic measuring turntable rotation number Vacuum cleaner in addition to wear debris.
The paint film abrasion device is arranged on the turntable by two wear grinding wheels. When the turntable rotates, one wear wheel on the left side is rubbed from the center of the surface of the outward sample, and one wear wheel on the right side is rubbed outward from the center of the surface of the sample plate. When the turntable rotates for one round, the traces worn on the surface of the template are composed of two circular rings that coincide with each other and intersect in an X shape. In this way, the advantage is that the surface of the template is rubbed in all directions, overcoming the shortcomings of the reciprocating wearer in one direction.
五;注意事项:
⑴ 测试结束后,应切断电源,清理仪器,将仪器罩好。
⑵ 长期不用时,应将砂轮取下放好。
⑶ 一年***年必须检修加油一次
Five; Note:
(1) After the test is finished, the power should be turned off, the instrument should be cleaned, and the instrument should be covered.
(2) When not in use for a long time, the grinding wheel should be removed and placed.
(3) One year to two years must be repaired once
声明:本站部分文章内容及图片转载于互联 、内容不代表本站观点,如有内容涉及侵权,请您立即联系本站处理,非常感谢!